Speedway Fits Mustang II Power Steering Conversion Kit

Speedway Mustang II Power Steering Conversion Kit. Is that steering wheel getting a little too heavy? Use this kit to convert that manual steering into power! Included is a power rack, pump and hardware to make everything fit.

All-new using premium internals/seals, this is NOT a remanufactured assembly. 15-1/2-inch center-to-center mounting works with aftermarket crossmembers. Can be retrofitted to 16-inch center-to-center Mustang II crossmembers using offset rack bushings. Includes inner tie rods with SAE 9/16-18 threads installed with jam nuts.

Includes steering rack mounting bushings for easy installation. 9/16-18 and 5/8-18 threads O-ring pressure and return ports.

Adapters to convert OE ports for use with AN -6 fittings and hose included. 15:1 performance steering ratio with 2-1/2-turns lock-to-lock. Pinion shaft uses industry standard ¾-inch-36 spline U-joints. Upgrade Your Mustang II IFS with Power Rack-and-Pinion Steering. There is little argument that the Mustang II independent front suspension (IFS) is one of, if not THE most widely used suspension designs for street rods, kit cars, and even updated classic muscle car suspensions. From weld-in frame stubs to full frame conversions, the Mustang II IFS offers a whole lot for your performance dollar. In one upgrade you give your project disc brakes, rack-and-pinion steering, better suspension geometry, and the ability to modify and update with all manner of aftermarket parts including drop spindles, coilover shocks, and more. Many Mustang II setups begin as budget systems with standard stamped steel control arms, small disc brakes, and manual steering.

Adding power steering provides better low-speed control, especially with larger tires, and allows a smaller diameter steering wheel to be fitted, often providing much sought-after interior room in the small cabins of street rods. Superior Build Quality with Direct Fit Ease. Have you tried to source an original or remanufactured'74-'78 Mustang II power steering rack lately?

They are getting harder to find and costs keep going up. However, a rodding trick that has grown in popularity is to upgrade to the Fox chassis Thunderbird rack-and-pinion due to its lower cost and ease of conversion. For most aftermarket Mustang II crossmembers it is a direct bolt-on swap thanks to the slotted mounting hole found on these newer crossmember designs. For those with older Mustang II crossmembers you can still fit the T-Bird rack by simply using offset rack bushings to change the center-to-center mounting bolt location to the wider 16-inch dimension used on the original Mustang II. Our T-Bird rack is not a remanufactured unit. It is built from an all-new casting and fitted with all new internals. That includes the rack gear, pinion shaft, internal seals, inner tie rods, and fluid lines. New mounting bushings are included and if your mounting hardware has seen better days we do offer a new. Some installations may require to properly space the rack away from the crossmember for clearance.

We offer these spacers along with the required for everything to mount up properly. We provide AN -6 hose adapters for the rack's inlet and outlet ports due to the Thunderbird rack-and-pinion fittings differing from the original Mustang II rack-and-pinion fittings.

This reduces frustration and installation time by allowing to be produced on site if your project is not already using AN power steering lines. The smaller 9/16-18 port is the "in"from your pump, while the larger 5/8-18 port is the return to your pump's reservoir. The T-Bird-based rack uses a 3/4-36 spline input shaft (manual is 9/16-26), requiring little more than a change at the rack end of your steering shaft in most installations.

If you are replacing an older power rack, then there should be no change to your steering shaft configuration. The Perfect Solution for Most Any Mustang II Configuration. A readily available power steering rack constructed from all new components and at a great value, what is not to love? Installation is a direct replacement for your manual rack in most instances due to the same Mustang II rack-and-pinion dimensions, and our T-Bird-based power steering rack will work with most any used in a modern serpentine belt drive or V-belt setup, including the Ford CII, GM Type II, and GM Type I (more commonly known as a Saginaw pump). These pumps output the necessary 1,200 psi required and flow approximately 3 GPM. We offer a multitude of in both V-belt and serpentine for Ford, GM, and Chrysler engine families to add the pump of your choice to your engine. Since there are so many variables that affect a properly functioning power steering system, including vehicle weight, alignment, steering wheel diameter, tire width, steering ratio, and much more, some applications may feel twitchy and may require a reduction in flow. The GM Type 1 and Type II pumps utilize that can easily be swapped out to adjust the flow down to aid in steering twitchiness and prevent steering dart due to an over-boosted power steering system.

Another option is an where you can dial in the exact steering effort you wish easily. This means you can have the system turned down for more effort when needed for a track day, but then it is easily turned back up to reduce your steering effort for daily driving. This is your best solution when using the Ford CII pump in a Ford-powered application as well. Our GM Saginaw style pump features all new components including reservoir and pump assembly. Includes billet chrome cap, new dipstick and hardware.

Pumps are 1200 PSI rated to work with most gearbox systems, 850 PSI valve available for Mustang II rack and pinion available upon request. Our Type II compact size pump is ideal for tight installations. For use with factory or remote reservoir tank depending upon part number. Perfect for street rods and custom vehicles with limited engine space. Pumps are available in chrome plated, various colors and plain, as cast finishes. Saginaw Style Power Steering Pump. (1) Tuff Stuff 6183B Direct Fit Saginaw Style Power Steering Pump. (1) Mustang II Power Steering Flow Valve for GM Pump, 2 GPM. (1) O-Ring to Inverted Flare Power Steering Adapter. (2) Mustang II Rack Spacer, 3/4 Inch. (1) Mustang II Rack & Pinion Bolt Kit - For Use With Rack Spacers. (2) Mustang II Outer Tie Rod End, Manual Version. (1) New T-Bird Power Steering Rack & Pinion for Mustang II Crossmembers. (1) T-Bird Offset Rack & Pinion Mount Bushings. Outer Tie Rod Ends Included. Related Items / Suggested Parts. Gotta Show 131101 Mustang/T-Bird Rack & Pinion Power Steering Hose Kit. 2033 Power Steering Pulley, 1 Groove, Backspaced. Power Steering Hose Kit for 1982-88 T-Bird Steering Rack to GM Pump. Please take advantage of the "add to cart" button on each listing to get everything in your cart prior to completing checkout. Speedway Motors is America's Oldest Speed Shop® and has been a trusted source for specialty rodding and racing products and friendly expert advice for more than 71 years. Repack the item in a sturdy box, include a copy of your invoice and complete the form on the back of the invoice. Speedway accepts full responsibility for the accuracy of our listings and product representation. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts & Accessories\Steering & Suspension\Other Steering & Suspension Parts". The seller is "speedway_motors" and is located in this country: US. This item can be shipped to United States, Denmark, Ireland, Netherlands, Slovakia, Slovenia, Lithuania, Portugal, Malta, United Kingdom, Cyprus, Australia, Austria, Hungary, Sweden, Spain, Estonia, Belgium, Finland, Bulgaria, Poland, Luxembourg, Czech Republic, Canada, France, Germany, Latvia, Italy, Greece, Romania.

Brand: Speedway Motors
Manufacturer Part Number: 9100481